DIN EN853 1SN Hydraulic Hoses: Specifications, Applications, and Selection Guide

18, Nov. 2026

 

DIN EN 853 1SN Hydraulic Hoses: Specifications, Applications, and Selection Guide

DIN EN 853 1SN is a single-wire-braid hydraulic hose type designed for conveying hydraulic fluids in systems where its pressure rating, fluid compatibility, temperature range, and routing requirements are suitable. Its construction generally consists of an oil-resistant synthetic rubber tube, one high-tensile steel-wire braid, and a protective rubber cover. The 1SN designation identifies a construction type, not one universal working pressure: pressure limits depend on hose size and the manufacturer’s published data. We recommend selecting by the complete assembly specification rather than by the 1SN label alone.

You can find more information on our web, so please take a look.

Key Takeaways

  • EN 853 1SN uses one steel-wire braid and is commonly selected for hydraulic lines in machinery and industrial equipment.
  • Nominal bore, working pressure, bend radius, fluid compatibility, and temperature limits must be checked for the specific hose size and product.
  • Common product ranges cover nominal bores from approximately 5 mm to 51 mm; availability and exact specifications vary by manufacturer.
  • For a reliable purchase, provide operating conditions, hose dimensions, end connections, and order quantity when requesting a quotation.

Who This Guide Is For

This guide is for procurement teams, equipment manufacturers, maintenance professionals, and hydraulic hose distributors comparing DIN EN 853 1SN products. It is useful when specifying replacement hose, planning a new hydraulic circuit, or requesting quotations from suppliers. We focus on practical selection and sourcing considerations rather than treating a standard designation as a substitute for a product datasheet. Final selection should be confirmed against the machine manufacturer’s requirements and the hose supplier’s technical documentation.

What Is a DIN EN 853 1SN Hydraulic Hose?

DIN EN 853 is a European hose standard covering rubber hoses for hydraulic applications, including specified construction and performance requirements. In the 1SN type, “1” refers to one steel-wire braid reinforcement layer, while “SN” identifies a standard wire-braid construction. The hose is intended for use in hydraulic systems with suitable fluids and service conditions. The exact construction materials and declared performance should be verified for the product being purchased.

Typical Construction and Materials

A typical 1SN hose has a synthetic rubber inner tube selected for compatibility with hydraulic fluids, a single braided steel-wire reinforcement layer, and a synthetic rubber outer cover. The reinforcement helps the hose contain internal pressure, while the cover protects against external exposure such as abrasion and weathering, subject to the manufacturer’s specifications. Not every hose cover has identical resistance to oils, ozone, or abrasion. Ask the supplier to confirm suitability where the installation involves unusual chemicals, outdoor exposure, or frequent contact with abrasive surfaces.

Specifications to Check Before Ordering

There is no single pressure value that applies to every EN 853 1SN hose. Working pressure and minimum bend radius vary with nominal bore and product design, so use the supplier’s data for the exact size rather than estimating from the standard name. The hose assembly, including its fittings and crimping method, must also be suitable for the system’s operating conditions. A hose with an adequate rating can still be unsuitable if its connections, fluid compatibility, or routing are incorrect.

Specification What to confirm Why it matters
Nominal bore Required DN or internal diameter Influences flow capacity and compatibility with the existing line
Working pressure Manufacturer’s rating for the selected size and assembly Must meet the system’s specified pressure requirements
Temperature Permitted fluid and ambient temperature ranges Heat and cold can affect hose life and performance
Bend radius Minimum radius for the selected hose size Over-bending can strain the reinforcement or restrict flow
Connections Fitting type, thread, orientation, and assembly details Prevents fitment problems and connection mismatches

Many suppliers list 1SN hoses across nominal bores from approximately 5 mm to 51 mm, but this is a broad market range, not a guarantee that every size is available in every product line. For example, DN 13 refers to a nominal bore of 13 mm; it does not, by itself, define the hose’s outer diameter or pressure rating. Some product catalogues give a typical temperature range of -40°C to +100°C for specified hydraulic fluids, but the approved range can differ by hose construction and fluid type. Confirm the applicable limits on the datasheet for the exact product and application.

Hengshui Xinchi Hose Manufacturing Co., Ltd. contains other products and information you need, so please check it out.

Applications and Hose-Type Matching

EN 853 1SN hoses are commonly considered for hydraulic circuits in industrial machinery, mobile equipment, agricultural machinery, and general-purpose hydraulic systems. Their suitability depends on the pressure, fluid, temperature, movement, and environmental exposure at the installation point. A static line in a protected machine enclosure may have different requirements from a hose exposed to repeated movement or external abrasion. Match the hose to the real duty cycle, not only to the equipment category.

When to Consider Another Hose Construction

A single-wire-braid hose may not be the right choice when the system requires a higher pressure rating, a different reinforcement construction, or special resistance to heat, chemicals, or severe external wear. In those cases, compare other hose types against the machine specification and supplier data. Do not replace a specified hose construction with 1SN solely because the diameter appears to match. If the original specification is unclear, identify the machine’s pressure and fluid requirements before selecting a substitute.

A Practical Selection Framework

  1. Identify the required size. Record the nominal bore, hose length, and any dimensional constraints. For a replacement, check the existing hose markings and measure carefully rather than relying only on a visual estimate.
  2. Confirm pressure conditions. Obtain the system’s normal and maximum specified pressures, including any relevant pressure surges. Compare these with the supplier’s rating for the selected hose and complete assembly.
  3. Check fluid and temperature compatibility. Name the hydraulic fluid where possible and provide the expected fluid and ambient temperatures. Request confirmation if the fluid is water-based, contains additives, or differs from common petroleum-based hydraulic fluids.
  4. Plan routing and movement. Check bend radius, hose movement, clamp positions, and proximity to hot or abrasive surfaces. Avoid twisting the hose during installation and follow the supplier’s assembly guidance.
  5. Specify the fittings and order details. Provide end connection standards, thread sizes, angles or orientations, quantity, and any packaging requirements. Ask whether the quotation covers hose only or finished hose assemblies.

Pricing, MOQ, and Lead Time

The cost of an EN 853 1SN order can vary with hose bore, length, reinforcement and cover specifications, fitting type, assembly work, order quantity, and packaging. Minimum order quantities and production or shipping lead times also depend on the selected product and current availability. We avoid quoting a fixed price or delivery schedule without those details because a hose-only order and a custom-fitted assembly are not equivalent purchases. For an accurate quotation, send a dimensional drawing or a clear written specification along with the required quantity and destination.

Supplier Evaluation Checklist

  • Can the supplier provide a datasheet for the exact hose size and construction?
  • Are working pressure, temperature limits, and minimum bend radius stated clearly?
  • Can the supplier confirm fluid compatibility and provide the relevant fitting options?
  • Are hose-only and finished-assembly pricing distinguished in the quotation?
  • Are MOQ, lead time, packaging, and requested documentation confirmed in writing?

As Hengshui Xinchi Hose Manufacturing Co., Ltd., we work with buyers sourcing hydraulic rubber hoses and can review application details to clarify the requested size, construction, and connection requirements. We recommend confirming the final specification before production, especially for assemblies that must match existing equipment. Product availability, customization options, and documentation should be discussed for each order rather than assumed. Clear specifications help both sides reduce quotation delays and avoid preventable fitment issues.

Conclusion: How to Choose the Right DIN EN 853 1SN Hose

DIN EN 853 1SN is a single-steel-wire-braid hydraulic hose type, but the designation alone does not determine whether a hose is suitable for a particular system. Select by nominal bore, size-specific working pressure, fluid compatibility, temperature range, bend radius, and fitting requirements, then verify the complete assembly against the equipment specification. The most practical next step is to prepare those operating and dimensional details before requesting quotations. Contact Hengshui Xinchi Hose Manufacturing Co., Ltd. with your hose size, application, fluid, pressure requirements, connection details, and quantity to discuss a suitable sourcing specification.

The company is the world’s best DIN EN853 1SN Hydraulic Hoses supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.